Back

Amplificador de Auriculares - Mezclador de Canales KA71

Re-stock: producto descontinuado por el fabricante. KA71 es un amplificador de auriculares con función adicional de mezcla de canales estéreo. Diseñado para ordenadores Amiga.

Más detalles

Referencia:
RP-KA71
Disponibilidad:
Producto no disponible


Indicarme cuando esté disponible

Añadir al carrito
69,75 € IVA incl.

KA71 es un amplificador de auriculares con función adicional de mezcla de canales estéreo. Diseñado para ordenadores Amiga. El chip de sonido Paula de Amiga envía dos de sus cuatro canales de audio al canal izquierdo y dos al canal derecho. Están completamente separados, lo que es molesto especialmente cuando se escucha con auriculares.

KA71 can mix stereo channels at a level adjustable with a knob, from full separation to mono output. It can be also used with computers having monophonic audio, or to mix two computers simultaneously playing parts of the same song. Of course one can also use KA71 as a regular headphone amplifier with smartphones, music players, computers and other sources.

WARNING: KA71 amplifier, depending on input signal, connected headphones and volume set, can produce sound pressure levels higher than 85 dB. High sound pressure level is harmful and may cause irrecoverable damages to your hearing sense. 85 dB is considered safe for continuous listening. Be careful turning the volume up and switch off the amplifier when changing signal sources!

Features:
• Freely adjustable stereo channels crossmixing from pass through to full mono.
• Can be used as mixer/pre-amp for a loudspeaker power amplifier or active loudspeakers.
• High output power, able to drive high-impedance phones.
• High audio quality, low distortions, low noise, wide bandwidth (10 Hz to 30 kHz).
• May be powered either via micro USB socket (from computer, USB hub, phone charger, powerbank), or 3 AAA batteries (one use or rechargeable).
• Batteries need not to be removed when using USB power, they are disconnected automatically.
• Selected high quality components. Only polyester and HQ aluminum electrolytic capacitors in the audio path.
• Modern design using mostly SMD parts.
• Durable aluminum encolsure.

Front Panel:

RastPort KA71 Front Panel

Power Supply:
The amplifier may be powered from USB or from batteries. It has a standard micro USB type B socket, the same as used in most of smartphones and tablets. Power requirements of KA71 are low, so it may be powered from any desktop computer, laptop, USB hub, phone charger or powerbank, using standard USB type A to micro USB type B cable. The amplifier only uses USB power, data lines are not connected inside.
In case when batteries are inserted and USB power is connected at the same time, batteries are automatically disconnected, so the device works on USB power. Then there is no need to remove batteries each time USB power is used.

Batteries:

KA71 uses three AAA size batteries. Accepted types are single use zinc or alkaline batteries, as well as rechargeable NiMH ones. To insert or replace batteries:
• Disconnect all the cables, switch off the power switch.
• Unscrew two front upper screws. Use a screwdriver with Phillips size 1 (PH1) tip.
• Unscrew two rear upper screws.
• Pull the upper half of enclosure up. It is not connected to anything.
• Remove old batteries if any (new amplifier comes without batteries installed).
• Insert new batteries, observing polarity, which is shown on the holder. If not sure, negative terminals should contact with springs.
• Put back the upper half of enclosure. Note that it only fits one way, you may need to turn it by 180°.
• Carefully screw in the screws. Note that a steel screw may damage aluminum thread easily. Start with bare hand, use screwdriver after making a few turns. Avoid excessive tightening.
• Verify that power LED lits when the power switch is switched on.

Remember:

• Even if you use rechargeable batteries, they are not being charged while USB power is connected. To recharge them you have to remove them from KA71 and use a standalone charger for NiMH batteries.
• Do not keep discharged batteries inside the device for a long time. Battery leak may seriously damage the amplifier.

Specifications:

   Physical:

   • Width: 88 mm.
   • Height: 38 mm.
   • Length: 130 mm.
   • Weight: 235 g (without batteries).

   Input:

   • Socket: mini jack 3.5 mm stereo.
   • Input impedance: 50 kΩ.
   • Maximum input signal amplitude: 5 Vp-p.
   • Voltage gain: 3.

   Output:

   • Socket: mini jack 3.5 mm stereo.
   • Rated peak output power (1 kHz sine wave, THD less than 0.01%):
      - 16 Ω load: 50 mW
      - 24 Ω load: 75 mW
      - 32 Ω load: 100 mW
      - 60 Ω load: 150 mW
      - 100 Ω load: 160 mW
      - 300 Ω load: 55 mW
      - 600 Ω load: 25 mW
   • Rated power bandwidth: 10 – 30.000 Hz (−3 dB power)
   • THD at rated power (32 Ω load):
      - Less than 0.01% at 1 kHz
      - Less than 0.05% in the whole passband.

   Power Supply:

   • Type: USB 5 V (via micro USB type B socket) or 3 × AAA cells inside, rechargeable (NiCd, NiMH) or single use (zinc, alkaline).
   • Batteries cut-off voltage: 2.7 V (0.9 V per cell).
   • Estimated battery operation time:
      - Alkaline 1000 mAh cells: 30 hours
      - Rechargeable 750 mAh NiMH cells: 20 hours.
   • Supply current, 32 Ω headphones (for batteries supply current depends on discharge level):
      - Idle (no signal): 16 mA from USB, 24 mA from batteries
      - Listening to pop music, loudly: 30 mA from USB, 35 mA from batteries
      - Continuous 1 kHz sine wave at 50 mW RMS: 175 mA from USB, 180 mA from batteries

For more Technical Specifications and Schematic Diagrams, please visit the manufacturer's website.


Sea el primero en hacer una consulta sobre este producto!

Consulta sobre el producto

*Campos Requeridos
Enviar

La consulta se ha enviado correctamente

Bienvenido

No hay productos

0,00 € Transporte
0,00 € Total

Transferencia

Sistemas de pago

8533
Product reviews